Your Questions About Wind Generators

Lisa asks…

Can you use a car alternator to build a wind generator?

I am very interested in trying to build my own small wind generator, I seen that you basically need a alternator, blades to build the fan, cabling and a battery. So could you use a car alternator and also how many 12V batterys would you need?
I think that was a little rude, judging by what you posted you seem to be a all around d*ck!

But thanks to the others who replied, you info was very helpful. thanks again.

admin answers:

You may have better success with an alternator with the field coils replaced with permanent magnets and the regulator removed. This will maximize the voltage output and allow you to regulate the voltage at the battery bank. The less electronics and other items to break up the tower the more reliable the system will be.

You should use deep cycle batteries, not automotive starting batteries. The number of batteries will depend upon the voltage your system operates, power capacity of the generator, and size of inverters. Do not go overboard with too many batteries or the generator will never be able to fully charge them.

There is someone near me who is building the blades with PVC pipe. He uses it to turn a permanent magnet DC motor to act as the generator. I’ll try to find his web page later.

I’m hoping to get back to my wind generator project shortly. It’s been tied up in municipal bylaws and idiotic permits…
Visit my web page for ideas.
Http://members.rennlist.org/warren/wind.html

Michael asks…

How to build a wind generator for a sailboat?

Does anyone have good plans for a small 24″ three blade wind generator ?

admin answers:

Hi,

You can try this set of plans :

http://www.agua-luna.com/wind_gene.html

But it will be good if you spray a protecting coating on it for make it marine grade.

The following steps were taking directly out of that DIY guide I offer to those who would like to run their homes on wind power safely, reducing their monthly utility bills or even selling power back the electrical companies.

“This manual is based on using a 260 VDC, 5 A continuous duty Treadmill Motor with a 6 inch threaded hub. These motors are available for under $50 from most motor surplus stores. We are getting about 7 amps in a 30 mph wind. In other words, it is a simple, cheap little machine to get you started. ”

“ASSEMBLY
1.Place the motor on top of the square tubing & bolt it in, using the two 5/16” x ¾” bolts.
2.Place the diode on the square tubing, about 2” behind the motor, & screw it into position using the self-tapping metal screw.
3.Connect the black wire coming out of the motor to the positive incoming terminal of the diode (Labeled AC on the positive side).
4.Connect the red wire coming out of the motor to the negative incoming terminal of the diode (Labeled AC on the negative side).
5.Center the tail over the square tubing, at the back end. Clamp your tail onto the side of the square tubing.
6.Using 2 self-tapping screws, screw the tail in place.
7.Place each blade on the hub so that all the holes line up. Using the ¼” bolts & washers, bolt the blades to the hub. For the inner three holes, use two washers per bolt, one on each side of the blade. For the outer three holes, just use one washer next to the head of the bolt. Tighten.
8.Hold the end of the shaft of the motor (which comes through the hub) firmly with pliers, & turn the hub counterclockwise until it tightens & stops.
9.Screw the nipple tightly into the floor flange using a pipe wrench.
10.Clamp the nipple in a vice so that the floor flange is facing up & level.
11.Place the square tubing (and everything that is on it) on top of the floor flange & move it so that it is perfectly balanced.
12.Through the holes of the floor flange, mark the square tubing at the point of balance.
13.Drill these two holes using a 5/32″ drill bit. You will probably have to take off the hub & tail to do this).
14.Attach the square tubing to the floor flange with two sheet metal screws.
For a longer life span of your wind generator, you should paint the blades, motor sleeve, mount & tail.”

Hope this helped, feel free to contact me personally if you have any questions if you’d like assistance in making your first self sufficient steps, I’m willing to walk you step by step threw the process. I’ve written several how-to DIY guides available at www agua-luna com on the subject. I also offer online & on-site workshops, seminars & internships to help others help the environment.

Dan Martin
Alterative Energy / Sustainable Consultant, Living 100% on Alternative & Author of How One Simple Yet Incredibly Powerful Resource Is Transforming The Lives of Regular People From All Over The World… Instantly Elevating Their Income & Lowering Their Debt, While Saving The Environment by Using FREE ENERGY… All With Just One Click of A Mouse…For more info Visit:

www AGUA-LUNA com

Good luck.

Powered by Yahoo! Answers